What batteries to use?

SmokeGENIE

18650 x 2 (FLAT TOP, Unprotected, 3.5v, 10A, 3000mah or above)

RC Haze Fan
18650 x 1 (FLAT TOP, Unprotected, 3.5v, 10A, 3000mah or above)

Remote
23A 12V x 1

See Battery Guide here

SmokeNINJA & SmokeNINJA PRO

18650 x 1 (FLAT TOP, Unprotected, 3.5v, 10A, 3000mah or above)

Haze Nozzle
Built-in 2000mAh Li-ion Battery

Remote
23A 12V x 1

See Battery Guide here

Back to Top

How long can the battery last?

Back to Top

How to charge my device?

SmokeGENIE

While the batteries are removable, all SmokeGENIE, SmokeNINJA & RC Haze Fan comes with USB-C charging function.We recommend using a 5V, 2A ~10W power source. 

If the machine is charging correctly, it will display the following signal:

Back to Top

How long to charge?

Back to Top

Why is my equipment not charging?

If the machine is charging correctly, it will display the following signal:

Since SmokeGENIE & SmokeNINJA have built-in charging protection, the machine will stop charging if the power source could damage the device. Please make sure a 5V, 2A ~10W power source is used. 

While it works with standard type USB-C cable, but there are too many variations on the market. We would recommend using the charging cable comes with your device. 

Please contact your local dealer or email CS@pmigear.com if further assistance is needed.

Back to Top

Can I use PMI fog machines in my studio?

Short answer - If the location is OK with water-based fog machines, it is OK with PMI fog machines.

Long Answer - The ingredients for PMI cloud formula is Vegetable Glycerine and Propylene Glycol, the same ingredient as common water-based formula.The only different is, due to the advance in atomizing technology, we no longer require actual water content in our formula.Since the effective ingredient is identical to Water-Based Liquid, the haze will have the same properties as the haze generated by Water-Based Hazer. So, if the studio is OK with Water-Based Hazer, it should be OK with PMI Hazer.

Back to Top

Working in cold temperture
(Below 10 Degrees Celsius)

In extreme cold temperatures (Below 10 Degrees Celsius), you might trigger "TIME OUT" warning, because of the liquid being less "runny" in the cold. In this case, simply perform one of the Fixes below:

FIX 1: Run the machine in low power setting - SmokeGENIE:
1) Set machine to LV 1 Smoke, LV 5 Wind.
2) Run for 1 minute.

SmokeNINJA/SmokeNINJA PRO:
1) Switch to Steam Mode
2) press trigger button 3 times to let the machine output continously. The machine will output for 1min/3min and stop automatically.

FIX 2: Place the chamber in warm area (above 20 Celsius) for 5 minutes. Install back to machine.

Back to Top

Why do I keep seeing "TIME OUT" warning?

"TIME OUT" means the heating unit inside the chamber is under fuelled and may cause overheating if it continues to operate. This is part of our protection system to keep the machine safe and durable. 

It could be caused by one of the following:

Outdoor Cold Weather (Below 10 Degrees Celsius)

In extreme cold temperatures (Below 10 Degrees Celsius), you might trigger "TIME OUT" warning, because of the liquid being less "runny" in the cold. In this case, simply perform one of the Fixes below:
 FIX 1:
Run SmokeGENIE/SmokeNINJA in low power setting for 30 seconds. SmokeGENIE: LV 1 Smoke, LV 5 Wind

Run SmokeNINJA & SmokeNINJA PRO: Steam Mode *SmokeNINJA & SmokeNINJA PRO can press trigger 3 times to output continously in steam mode for warm up.

 FIX 2: Place the chamber in warm area (above 20 Celsius) for 5 minutes. Install back to machine.

Fog Liquid level is low

Check the liquid level of the Chamber.
Machine will keep showing "TIME OUT" when fog liquid is almost out. This can be solved by simply refilling the Chamber. See refill instructions below:

SmokeGENIE/SmokeNINJA is tilting downwards

Make sure the machine is not operating downward. Due to the design of the chamber, it can only operation upside down for a short period of time (~1 min) and needs to be refuel between pulses.

If you need your smoke to flow downward, simply use our accessories and nozzles to guide the smoke downward.

Chamber is not installed properly

When Chamber is not installed correctly, or there is dirt in the adapter, it may affect the connectivity. Perform the following steps to ensure this is not causing the issue:
1)     Remove the chamber form machine
2)     Clean the adapter on both chamber and machine
3)     Reinstall and tighten chamber until you feel resistance.

SmokeGENIE is in smoke levels 6 – 10 (SmokeGENIE ONLY)

Since smoke levels 6 – 10 in “PRO MODE” are designed for intense short bursts, which will cause liquid to dry out faster. This is completely normal, you just need to wait for the message to disappear after 3 seconds, then you can start again.

If you want to make longer pulses of over 10 seconds, we suggest using smoke levels 1 – 5.

Chamber is Damaged

Each chamber is expected to support ~100 hours of spray time.
Chamber will reach the end of its lifecycle after ~100 hours of spray time or shorter if Chamber is forced to output repeatedly, ignoring the “TIME OUT” warning.
This normally company with a light burnt odour in the smoke.
If this is the case, it is highly likely that the chamber is damaged and has reached the end of its lifecycle. Please replace a new chamber.

Please do not hesitate to contact us at CS@pmigear.com directly if you are unable to resolve your issue

Back to Top

Can the machine work as a hazer?

Both SmokeGENIE & SmokeNINJA can be used as a hazer.

Recommended Studio Size:
SmokeGENIE: 3,000sqft (~300sqmt)
SmokeNINJA PRO: 1,000sqft (~100sqmt)
SmokeNINJA: 500sqft (~50sqmt)

Back to Top

How fast can it haze up a room?

SmokeGENIE

Both SmokeGENIE & SmokeNINJA has a 500CFM output. Meaning both SmokeGENIE & SmokeNINJA can haze a 500sqft studio with 1 min of spray time.

For larger spaces, we recommend using the SmokeGENIE. When used with Haze fan, each unit of SmokeGENIE can support hazing for sutdio up to 3,000sqft(300sqmt).

See below a video showing how SmokeGENIE haze up a 1,500 sqft stuio space in  under 2 mins:

Back to Top

Does the machine support continuous smoke output?

SmokeGENIE

SmokeGENIE is designed survive the intense production. All 5 power levels in standard mode can support continue output until the battery or chamber runs dry.

For LV 6-10 in "PRO MODE", they are designed for intense short burst. Here is the expected continous burst time for each power settings:

SmokeGENIE 10 minute burst test

SmokeNINJA & SmokeNINJA PRO:

SmokeNINJA can suport 1 minute of continuous spray at max power setting.

SmokeNINJA PRO with Gen 3 Clean Fog Techology, can support 3 minutes of continuous output at max power setting.

Back to Top

Why is the device spitting liquid?

This is caused by heating unit inside the chamber getting oversoaked with fog liquid. This does NOT damage the condition of the chamber, and here is how to fix it:

How to clean the chamber to prevent liquid leaking

1. Remove chamber

2. Make sure silicone cap is closed shut

3. Wipe clean the chamber

4. Place it upside down on a napkin for 2 mins

5. Tap a few times to remove residue

Back to Top

Is there a limit on Operation Angle?

Both SmokeGENIE & SmokeNINJA can support 360-degree operation, but due to the design, they will have a time limit when sprayed downward. 

SmokeGENIE's time limit 

SmokeNINJA's time limit

For downward spray over a minute, we recommend using the nozzle kits to re-direct the smoke:

Back to Top

How to replace the chamber?

Back to Top

How to Refill?

To refill, simply lift up the silicone cap on top of the chamber and fill it with the liquid comes with the device. 

Make sure to CLOSE the silicone cap tightly after refill.

Back to Top

When to replace the chamber?

There are 4 signs to look for that hints at a damaged chamber:

1. When the machine displays "TANK FAULTY" when chamber is installed.
2. When the Chamber starts to produce an unpleasant burning smell (Usually after ~100 hours of spray time.)
3. Machine keep prompting "TIME OUT" warning during normal operation.
4. When the smoke becomes very pale even in high smoke levels.

In these 4 cases, it is highly likely that the chamber is damaged, or has reached the end of its lifecycle. Please replace a new chamber.

Back to Top

How long can a chamber last?

Each Chamber is designed to support 100 Hours of smoke output.

Back to Top

Is the Cloud Formula a water-based or oil-based liquid?

Short answer - PMI fog machines use a water-based liquid without water content.

Long Answer – the effective ingredient in Oil-Based haze liquid is mineral oil, hence the name “Oil-Based”. It is known to produce a fine and long-lasting haze but at the same time might cause health issue when inhaled and leaves a fine residue on every inch of the room after the haze. Making it incompatible with expensive equipment.

For Water-Based Hazer, while the liquid is 7-80% water, the water is mainly serves as an expending agent and cooling agent, since steam will dissipate quickly, it doesn’t contribute much to the haze effect. In Water-Based Liquid, the effective ingredients are Vegetable Glycerine and Propylene Glycol. The haze generated with Vegetable Glycerine and Propylene Glycol do not last as long when compared to the haze generated with mineral oil, but at the same time, it does not leave residue on equipment surface.

PMI Fog machines use Vegetable Glycerine and Propylene Glycol our effective ingredients, same as Water-Based Hazer.

However, thanks to advancement in atomizing technology, we no longer require actual water content in our formula. This results in great reduction in liquid and power consumption. PMI hazers can generate the same amount of haze with 1/10 of liquid and power consumption.

Since the effective ingredient is identical to Water-Based Liquid, the haze will have the same properties as the haze generated by Water-Based Hazer. So, if the studio is OK with Water-Based Hazer, it should be OK with PMI Hazer.

Back to Top

What is the liquid consumption?

Back to Top

Why is my chamber leaking?

SmokeGENIE

Leakage is mostly likely caused by the following:

• Silicone tap not being close tightly.
• Excessive Liquid accumulated inside the smoke output.Chamber is not stored inside the capsule/ installed on machine.
• Removing the excessive Liquid with the following steps should stops the leaking.

Also make sure the Chamber is either stored inside the capsule or installed properly on the machine.

Back to Top

How to store leftover liquid? Is there an expiration date?

When store in the air-tight chamber, in room temperature and away from sunlight, the leftover liquid can have over 6 months of shelf life.

Back to Top

How long can one bottle last?

Both SmokeGENIE & SmokeNINJA uses the highly condensed Cloud Formula and is much more efficient compares to liquid used on traditional fog machines.

The liquid consumption at max level is 0.5ml/min. Meaning that 100ml bottle can support 200mins of spray time at MAX power.

Back to Top

What is the signal type & Operation Range of the remote?

Back to Top

Remote signal is weak

This is likely caused by low remote battery.

Please check if the red light is dim or blinking when remote is pressed. If so, the battery level might be low, and should be replaced. 

Back to Top

How to pair the remote?

Below is a video instruction on how to pair the remote:
Magic Remote Pairing instruction

Back to Top

How to switch Control Setting
(Continuous/Pulse/Burst)?

Below is the video instruction on how to switch control settings:
Changing control setting to Continuous/Pulse/Burst mode

Back to Top

What does warranty covers?

Our 2-year warranty for the SmokeGENIE & SmokeNINJA is eligible to all users who bought from our authorised dealers.

The warranty covers any defect due to manufacturing; any issues caused by FIRE, WATER or PHYSICAL damage is NOT COVERED.

The chamber is considered as a consumable and is therefore NOT covered by this warranty unless its damaged upon receipt.

During the warranty period, users can contact their local dealer or email us at CS@pmigear.com for direct machine support.
Please supply us with the MACHINE SERIAL NUMBER, which can be found inside the battery cover and behind the remote:

Back to Top