Magic Remote Tutorial

DEFAULT REMOTE SETTINGS

ADVANCED REMOTE FUNCTIONS

Back to Tutorial Page

DEFAULT SETTING - PRO KIT & STARTER KIT

By default, SmokeGENIE and RC Haze Fan will only operate when button is pressed down (Trigger Mode) and is paired to Button "A" on the remote. 
 

You can press and hold button "A" to turn on SmokeGENIE & RC Haze Fan.

 

For continues spray, you can switch to Continuous Mode - 
Turn SmokeGENIE & RC Haze Fan OFF & ON. Within 30 seconds, PRESS AND HOLD button "B" & "D" for 5 seconds. 
Red light will flash at bottom of SmokeGENIE to indicate the machine is now in Continuous Mode. 
In Continuous Mode, the new control setting is as below: 
Press button "A" - SmokeGENIE will run continuously.
Press button "B" - Turns off SmokeGENIE.
You can switch the control setting on RC Haze Fan using the same procedure above. 

 

Switching back to Trigger Mode -
Turn SmokeGENIE & RC Haze Fan OFF & ON. Within 30 seconds, PRESS AND HOLD button "B" & "C" for 5 seconds.
 

Back to Top

DEFAULT SETTING - EVENT KIT

The default setting of Event Kit is designed to optimize the experience using GENIE trident.
We strongly recommend installing the SmokeGENIEs on Trident according to the number marking before using. 

 

Press Button "C" to turn ON all 3 SmokeGENIEs & RC Haze Fans.

Press Button "D" to turn OFF all 3 SmokeGENIEs & RC Haze Fans.

 

To operate 1 - 2 units of SmokeGENIE, follow the chart below:

BUTTON A

 Turns on SmokeGENIE #2  

BUTTON B

 Turns on SmokeGENIE #1 & 3

BUTTON C

 Turns on SmokeGENIE #1, 2 & 3 + All RC Haze Fan

BUTTON D

 Turns off all SmokeGENIEs + RC Haze Fans

  

Back to Top

PAIR & ERASE REMOTE BUTTON

NOTE: To avoid mis-triggering, SmokeGENIE will only response to Pair/Erase signal 30 seconds after it’s been turn on.

ALWAYS turn SmokeGENIE OFF & ON again using the power button before the pairing.

PAIR A NEW BUTTON

1. Locate the "SET" indication light at the bottom of SmokeGENIE. There is a hole near the "SET" logo. You can see indication light through this hole. This will assist you through the pairing process.

2. Turn SmokeGENIE OFF & ON again using the power button.

3. Within 30 seconds, press and hold button “C” & “D” for 5 seconds to enter the Pair Mode.
The "SET" light at bottom of SmokeGENIE (or side of RC Haze Fan)will turn on, indicating the pairing function is successfully activated.
 
4. PRESS the button you want to pair 4 times - Red light will flash at the bottom of SmokeGENIE each time it receives a signal. Now the button is paired and you should be able to use that button to trigger SmokeGENIE.
Each SmokeGENIE can be paired to up to 4 remote buttons.

 Erase all the buttons paired

NOTE: To avoid mis-triggering, SmokeGENIE will only response to Pair/Erase signal 30 seconds after it’s been turn on.

ALWAYS turn SmokeGENIE OFF & ON again using the power button before the erasing.

WARNING: Once you Erased a SmokeGENIE you will need to pair a new button to SmokeGENIE before you can use a remote to control it again.

1. Turn SmokeGENIE OFF & ON again using the power button.

2. Within 30 seconds, press and hold button “A” & “B” for 5 seconds to enter the Erase Mode.

 

The SET light at bottom of SmokeGENIE (or side of RC Haze Fan) will flash to indicate erase is successful. 
All buttons previously paired to the SmokeGENIE is now erased.
 

SWITCH CONTROL SETTING(TRIGGER/ CONMTINUOUS/ PULSE)

Warning: Before switching to Continuous Mode or Pulse Mode, ensure that both the "START" button and "STOP" button are properly paired. Follow the instructions below to pair the start and stop buttons before changing to these modes.

Warning: During Continuous Mode, ensure that the machine has sufficient liquid before use to avoid overheating the chamber. Always check the liquid level before each session

Pairing Start Button & Stop Button:

NOTE: To avoid mis-triggering, SmokeGENIE will only response to Pair/Erase signal 30 seconds after it’s been turn on.

1. Locate the "SET" indication light at the bottom of SmokeGENIE. There is a hole near the "SET" logo. You can see indication light through this hole. This will assist you through the pairing process.

2. Turn SmokeGENIE OFF & ON again using the power button.

3. Within 30 seconds, press and hold button “C” & “D” for 5 seconds to enter the Pair Mode.
The "SET" light at bottom of SmokeGENIE (or side of RC Haze Fan)will turn on, indicating the pairing function is successfully activated.

4. Once the Pairing Mode is activated, SmokeGENIE will set the first signal it receives next as the ON button, and the next three signals it receives as the OFF button.
For example, if you want to set Button "A" on the Magic Remote as the ON button and Button "B" as the OFF button, press the buttons in the following sequence: "A" → "B" → "B" → "B"

    Each time SmokeGENIE successfully receives a signal, a red light will flash at the bottom of the machine. 

    Switch Control Setting:

    NOTE: To avoid mis-triggering, SmokeGENIE will only response to Switch Control Setting 30 seconds after it’s been turn on.

    To switch the control setting, turn the smokeGNEIE or Haze Fan off & on again. Within 30 seconds, press and hold the button combination below for 5 seconds.

    MDOES WHAT IT DOES BUTTON COMBINATION

    Trigger

     

    SmokeGENIE & Haze Fan only operates when button is pressed

     

    B+C

     

    Continuous 

     

    Press ON button and SmokeGENIE will run continuously until OFF button is pressed.

     

    B+D

     

    Pulse

     

    Press ON button and SmokeGENIE will run in 3 seconds pulses continuously until OFF button is pressed.

     

    A+C

     

    3 secomds burst

     

    SmokeGENIE & Haze Fan operates for 3 seconds when button is pressed

     

    A+D

     

    PAIRING MULTIPLE UNITS